热门关键词:
毕业论文(设计)单级离心泵设计
  • 该文件为doc格式
  • 文件大小:838.83 KB
  • 下载次数
  • 文件评级
  • 更新时间:2020-06-09
  • 发 布 人lordvoldemorte
  • 文件下载:
  • 立即下载

  • 文件介绍:
  • 该文件为 doc 格式,下载需要 1 积分
  • 毕业论文(设计)单级离心泵设计单级离心泵设计

    摘 要
    本设计从离心泵的基本工作原理出发,进行了一系列的设计计算。考虑离心泵基本工作性能,流量范围大,扬程随流量而变化,在一定流量下只能供给一定扬程(单级扬程一般10~80m)。本设计扬程为50m,泵水力方案通过计算比转数(n=67.5)确定采用单级单吸结构;通过泵轴功率的计算确定选择三相异步电动机;由设计参数确定泵的吸入、压出口直径;通过叶轮的水力设计确定叶轮的结构以及叶轮的绘型;设计离心泵的过流部件,确定吸入室为直锥形吸入室,压出室为螺旋形压出室;设计轴的结构及进行强度校核;确定叶轮,泵体的密封形式及冲洗,润滑和冷却方式;通过查标准确定轴承,键以及联轴器,保证连接件的标准性。从经济可靠性出发,合理设计离心泵部件,选择标准连接件,保证清水离心泵设计的安全性,实用性,经济性。

    关键词:离心泵工作原理;水力方案设计;叶轮和过流部件设计;强度校核;密封设计;键、轴承的选择

























    Centrifugal Pump Design Manual

    Abstract : This design starting from the basic working principle of the centrifugal pump, conducted a series of design calculations. consider the basic centrifugal pump performance, flow in a wide range, lift varies with the flow, the flow can only supply some lift (single-stage lift is generally 10~80m).The design head is 50m ,the design of the pump hydraulic scheme by calculating the number of revolutions(n=67.5) to determine the single-stage single-suction structure; choice of motor shaft power calculation; design parameters to determine the pump suction outlet diameter; determine the structure of the impeller and the impeller of the drawing of the hydraulic design of the impeller; flow parts of the design of centrifugal pump suction chamber for straight conical suction chamber, pressed out of the spiral-shaped pressure chamber; the structure and strength check of the axis design; determine the impeller centrifugal pump seal design, pump closed form and washing, lubrication, cooling method; determined by checking the standard bearings, and coupling to ensure that the standard connection. Departure from the economic viability of the rational design of centrifugal pump components, select the standard connector, to ensure the water using a centrifugal pump design safety, practicality, economy.

    Keyword: Centrifugal pump working principle ; Hydraulic design; Component design
    of the impeller and the over current; Strength check; Seal design; The choice of key and bearing
















    目 录
    1 绪论 1
    2 电动机的选择 2
    2.1 原动机概述 3
    2.2 原动机选择 3
    2.2.1 泵有效功率 3
    2.2.2 泵轴功率 3
    2.2.3 泵计算功率 3
    2.3.4 选择电动机 4
    3 泵主要设计参数和结构方案确定 5
    3.1 设计参数 5
    3.2 泵进出口直径 5
    3.2.1 泵吸入口径 5
    3.2.2 泵排出口径 5
    3.3 泵转速 5
    3.4 泵水力结构及方案 6
    3.5 泵的效率 7
    3.5.1 泵总效率 7
    3.5.2 机械损失和机械效率 7
    3.5.3 容积损失和容积效率 8
    3.5.4 水力损失和水力效率 8
    4 离心泵泵轴及叶轮水力设计计算 9
    4.1 泵轴及其结构设计 9
    4.1.1 泵轴传递扭矩 9
    4.1.2 泵轴材料选择 9
    4.1.3 轴结构设计 9
    4.2 叶轮进口直径 10
    4.3 叶片入口边直径 10
    4.4 叶片入口处绝对速度 11
    4.5 叶片入口宽度 11
    4.6 叶片入口处圆周速度 11
    4.7 叶片数Z 11
    4.8 叶片入口轴面速度 11
    4.9 叶片入口安装角 12
    4.10 叶片厚度 12
    4.11 叶片排挤系数校核 12
    4.12 叶片包角的确定 13
    4.13 叶轮外径 13
    4.14 叶片出口安装角 13
    4.15 叶轮出口宽度 13
    5 叶轮的选择及绘型 15
    5.1 叶轮选择 15
    5.2 平面投影图画法 15
    5.3 轴面投影图画法 15
    6 离心泵的吸入室及压出室设计 18
    6.1 吸入室设计 18
    6.1.1 概述 18
    6.1.2 直锥形吸入室设计 18
    6.2 螺旋形压出室 18
    6.2.1 基圆 18
    6.2.2 蜗室入口宽度 19
    6.2.3 舌角 19
    6.2.4 泵舌安装角 19
    6.2.5 蜗室断面面积 19
    6.2.6 扩散管 21
    7 轴向力径向力平衡计算 22
    7.1 轴向力及其平衡 22
    7.1.1 轴向力计算 22
    7.1.2 轴向力的平衡 23
    7.2 径向力及其平衡 23
    8 轴承、键、联轴器的选择 24
    8.1 轴承 24
    8.1.1 轴承选择 24
    8.1.2 轴承校核 24
    8.1.3 轴承润滑 25
    8.1.4 轴承密封 25
    8.2 键的选择与校核 25
    8.2.1 键的选择 25
    8.2.2 键的强度校核 26
    8.3 联轴器选择 26
    8.3.1 联轴器 26
    8.3.2 联轴器的强度校核 27
    9 泵轴的校核 29
    9.1 强度校核 29
    9.2 刚度校核 31
    9.3 临界转速校核 31
    10 泵体及其部件的密封设计 33
    10.1 叶轮密封 33
    10.2 泵体密封 33
    10.3 轴封设计 33
    10.3.1 密封腔处的介质压力 34
    10.3.2 密封面平均直径的圆周速度 34
    10.3.3 密封腔内的介质温度 34
    10.3.4 根据介质特性选型 34
    10.3.5 机械密封具体结构 34
    10.4 机械密封辅助措施 35
    10.4.1 机械密封冲洗 35
    10.4.2 机械密封润滑 35
    10.4.3 机械密封冷却 35
    11 经济性分析 36
    12 结论 37
    参考文献 38
    致谢 39



















    1 绪论...
文档留言
验证码: 请在右侧输入验证码 看不清楚,换一个